Argon vs Argon Helium Mix for Welding: Which Gas Fits Your Job?

Disclosure: This post contains affiliate links and I will be compensated if you make a purchase after clicking through my links. Learn More

The argon vs argon helium mix for welding choice comes down to heat. Pure argon fits most TIG work, thin metal and steady arc starts, and an argon helium mix fits thick aluminum and copper that need a hotter arc and deeper penetration.

Both gases are inert, so neither one reacts with the weld pool. The difference sits in how they carry heat, how easy they make the arc start and how much gas you burn per hour.

We pulled the numbers from ESAB, Hobart Brothers, Miller and The Fabricator so you can match the gas to the job.

Argon vs Argon Helium Mix at a Glance

FeaturePure ArgonArgon Helium Mix
Arc heatLower, softer arcHotter arc; about 2 to 3 V higher at the same arc length (ESAB)
PenetrationNarrower, deeper centerWider, broader penetration
Arc startsEasy, consistent high frequency startsLess consistent as helium rises
AC cleaning on aluminumGood cleaning actionLess used on AC above 25% helium
Flow rateBaseline (TIG usually 10 to 35 cfh)50% or more over argon in the flat position
Bead lookBrighter, shinier surfaceOften needs wire brushing
CostLowerHigher per cylinder
Best fitThin metal, steel, stainless, most TIGThick aluminum, copper, faster travel

What Is Argon Shielding Gas?

Argon is an inert gas and the most common shielding gas for TIG and aluminum MIG. Miller calls 100% argon the best all-around TIG gas because it is affordable, easy to find and starts the arc reliably.

Argon is about 1.4 times heavier than air and 10 times heavier than helium, per The Fabricator. That weight lets it blanket the weld pool well in the flat position.

Argon has a low ionization potential, so the arc lights easily and stays stable. On AC TIG aluminum, ESAB notes that pure argon gives good arc stability, better cleaning action and better arc starting.

What Is an Argon Helium Mix?

An argon helium mix blends helium into argon to make a hotter arc. Common blends run from 25% helium up to 75% helium, according to Miller and ESAB.

Helium has a higher ionization potential and higher thermal conductivity than argon. Hobart says the result is more weld penetration, a wider weld root and less porosity.

Gas suppliers sell these blends premixed. For TIG, Hobart lists 25% helium and 75% argon. For MIG on aluminum, Hobart lists 75% helium and 25% argon.

TIG welding aluminum with pure argon vs argon helium mix side by side

Credit: www.youtube.com

Argon vs Argon Helium Mix for Welding: Key Differences

The key differences are arc heat, penetration shape, arc starting, gas flow and cost. Helium adds heat and speed, and argon adds control and easy starts.

Arc Heat and Voltage

ESAB says adding helium to argon raises arc voltage by 2 or 3 volts at the same arc length. More voltage at the same amperage means more heat goes into the joint.

Miller puts it simply: as helium content goes up, the arc gets hotter. That extra heat helps on aluminum and copper, which pull heat away from the weld fast.

Penetration and Bead Shape

Pure argon makes a relatively narrow penetration profile. ESAB says that narrow shape has a higher chance of trapping gas, which shows up as porosity.

Helium widens the penetration. ESAB reports the broadest profile at about 75% helium and 25% argon for MIG. That shape helps prevent incomplete fusion on heavy plate and double-sided groove welds.

Arc Starting and Stability

Argon gives consistent high frequency start performance because of its low ionization potential. Miller notes that helium makes arc starts less consistent as its share rises.

On AC TIG, Hobart warns that helium content above 25% may cause arc instability. ESAB agrees that higher helium blends on AC are used, but not often.

Gas Flow Rate

Helium is lighter than air, so it floats away from the weld. The Fabricator says helium blends in the flat position can need 50% or more flow than pure argon.

Miller lists typical TIG flow at 10 to 35 cfh. If your torch runs 20 cfh on pure argon, plan on about 30 cfh or more with a helium blend, then fine tune from the bead. Our MIG gas flow rate chart covers MIG starting points.

Do not overcorrect. The Fabricator warns that too much flow can create a venturi effect that pulls air into the weld zone.

Weld Appearance

ESAB says pure argon usually leaves a brighter, shinier weld surface. A helium blend weld on aluminum often needs post-weld wire brushing.

Hobart adds that helium raises weld discoloration on aluminum because more magnesium burns off in the arc.

Cost and Gas Use

Helium blends cost more than pure argon, and both ESAB and Hobart list cost as a downside. You also burn more gas per hour because of the higher flow.

ESAB notes that faster travel speed can offset that cost on production work. Prices change by region and supplier, so ask your gas supplier for a current quote on both gases and on the welding gas cylinder size you plan to rent.

Where Each One Fits

Use this table as a starting point, then follow the filler and machine maker charts for your exact job.

JobBetter gasWhy
Aluminum under 1/16 in (1.6 mm)Pure argonThe Fabricator suggests pure argon below 1.6 mm
General AC TIG aluminumPure argonGood cleaning action and stable AC arc
Thick aluminum TIG25% He / 75% ArDeeper root penetration, faster travel
Thick aluminum MIG75% He / 25% ArBroadest penetration, less porosity
Copper and other heat sinksArgon helium blendExtra heat offsets heat loss
DCEN machine TIGUp to 90% He / 10% ArESAB lists high helium for DCEN machine welding
Overhead TIGHelium blend can helpHelium floats up into the joint
Carbon steel and stainless TIGPure argonMiller calls argon the best all-around TIG gas
TIG welding thick billet aluminum with a helium argon mix for deeper penetration

Credit: www.youtube.com

Gas purity matters with both choices. Hobart calls for argon at 99.997% minimum purity with a dew point of -76°F or lower, and helium at 99.995% with a dew point of -71°F or lower.

Safety With Argon and Helium

Argon is heavier than air, so it can collect in pits, tanks and low corners and push out the air you breathe. Ventilate confined spaces and never weld inside a closed tank without a confined space plan.

Chain or strap every cylinder upright, keep the valve cap on during transport and close the valve when you finish.

Which One Should You Choose?

Most home and small shop welders should start with pure argon. Move to a helium blend only when thick aluminum or copper runs out of heat on your machine.

Choose pure argon if:

  • You TIG weld steel, stainless steel or thin aluminum.
  • You want easy, repeatable high frequency start performance.
  • You weld AC TIG aluminum with a small or mid-size machine.
  • You want the lowest gas cost and a shiny bead.

Choose an argon helium mix if:

  • You weld aluminum or copper thicker than your machine handles on argon.
  • You need deeper root penetration and less porosity on heavy plate.
  • You want faster travel speed on production welds.
  • You MIG weld aluminum and need more fusion at the toes.

If you are new to TIG welding gas choices, start with one argon cylinder and add a 25% helium blend later for thick parts.

Frequently Asked Questions

Is an argon helium mix better than pure argon for TIG?

It is better only when you need more heat. Miller calls 100% argon the best all-around TIG gas. A 25% helium, 75% argon blend helps on thick aluminum and copper, where it adds penetration and travel speed. On thin metal, pure argon gives easier arc starts and better control.

What is the best helium mix for TIG welding aluminum?

Hobart lists 25% helium and 75% argon as the TIG blend for deeper root penetration and less porosity. Hobart and ESAB both warn that more than 25% helium can make an AC TIG arc unstable. Higher helium blends usually belong to DCEN machine welding.

Do you need a higher flow rate with helium mix?

Yes. Helium is much lighter than argon, so it rises away from the weld faster. The Fabricator notes that helium blends in the flat position can need 50% or more flow than pure argon. Start at the higher flow, then check the finished bead for porosity.

Can you MIG weld aluminum with argon helium mix?

Yes. ESAB lists MIG blends from about 25% helium up to 75% helium in argon. Hobart recommends 75% helium and 25% argon when you want deeper root penetration and less porosity on aluminum. Pure argon stays the most common MIG gas for thinner aluminum.

Why do welders add helium to argon?

Helium has a higher ionization potential and thermal conductivity than argon. ESAB says adding helium raises arc voltage by 2 or 3 volts at the same arc length. That hotter arc gives wider penetration, faster travel and less porosity on thick, heat-hungry metals like aluminum.

Final Words

Pure argon is the default for most TIG work and thin aluminum MIG. It starts easily, cleans aluminum well on AC and costs less.

An argon helium mix earns its place on thick aluminum, copper and production welds. Expect a hotter arc, wider penetration, higher flow and a higher gas bill.

Keep helium at 25% or less for AC TIG, raise your flow rate and test on scrap before the real part.

Scroll to Top