Disclosure: This post contains affiliate links and I will be compensated if you make a purchase after clicking through my links. Learn More
How does underwater welding work? It is arc welding done below the waterline, where the heat of the arc boils the surrounding water into a gas bubble that shields the weld. Crews weld either directly in the water or inside a dry, pressurized chamber.
TWI also calls this hyperbaric welding, because the work happens at higher pressure than on land. Divers use it on ships, dams, pipelines, harbor works and offshore platforms.
Wet welding and dry welding use different gear and different processes, and they give different weld quality.
How Does Underwater Welding Work in Wet Conditions
In wet welding, the diver strikes an arc right in the water. TWI explains that the arc heat vaporizes the water around it, which acts like the shielding gas around an arc in air.
That vapor is roughly 70% hydrogen, 25% carbon dioxide and 5% carbon monoxide, per TWI. The bubble layer protects the weld, but it also clouds the diver’s view of the joint.
Most wet welding uses stick electrodes with a waterproof coating over the flux coating. TWI also lists a flux cored wire method with no shielding gas, and a semi-automatic method that uses solid wire and gas held inside a water curtain.

Credit: www.youtube.com
The Wet Welding Circuit
Underwater welding runs on direct current, not alternating current, according to TWI. The welding power source stays on the surface or on the support vessel.
A surface crew controls the power through a double-pole knife switch. TWI says the current is switched on only when the diver calls for it and off right after welding stops.
The diver uses an insulated electrode holder and wears rubber gloves. TWI stresses that the diver must be completely insulated from the welding circuit.
What Is Dry Hyperbaric Welding?
Dry welding moves the arc out of the water. The diver works inside a sealed chamber that is pressurized to match the surrounding water depth, as the AWS Welding Digest describes.
TWI says the chamber gas is usually a mix of oxygen and helium, set at a pressure that protects the welder from decompression sickness.
Types of Dry Welding Enclosures
| Enclosure | How it works | Who fits inside |
|---|---|---|
| Habitat | Large chamber built around the work, often used for hot work | Two or three divers in larger habitats |
| Dry chamber | Smaller chamber that holds the welder’s upper body | One welder, head and torso |
| Dry spot | Small chamber placed over the weld area only | Torch or gun reaches in |
Inside a dry habitat, divers can use TIG welding, MIG welding and plasma arc welding. TWI lists all three as dry processes.

Credit: www.youtube.com
Wet vs Dry Underwater Welding
Wet welding is faster to set up. Dry welding gives better welds. That trade-off drives most job decisions.
| Factor | Wet welding | Dry (hyperbaric) welding |
|---|---|---|
| Where the arc burns | In the water | In a gas-filled chamber |
| Main processes | Stick, flux cored wire | TIG, MIG, plasma arc |
| Setup | Quick access to the structure | Chamber must be built and sealed |
| Visibility | Limited by bubbles and water | Better visibility and control |
| Weld quality | Lower; fast cooling and hydrogen | Higher; more control over conditions |
| Typical use | Repairs and maintenance | Pipelines and high-quality structural welds |
The AWS Welding Digest notes that wet welding is common for repairs and maintenance because crews can reach submerged structures quickly. Dry welding wins on visibility and environmental control.
Why Underwater Welds Are Harder to Get Right
Water pulls heat out of the joint fast. TWI says the welded joint may cool too quickly, and the bubbles can disturb the weld pool. Both raise the risk of defects such as cracking.
Hydrogen is the other big problem. TWI reports diffusible hydrogen up to 100 ml per 100 g of weld metal with rutile electrodes and about 25 ml per 100 g with oxidizing electrodes.
Those levels climb as depth increases, which raises the risk of hydrogen-assisted cracking. TWI adds that judging wet weld quality can be difficult.
AWS D3.6M is the code for underwater welding. The AWS Welding Digest says it sets qualification requirements, inspection criteria and acceptance standards for underwater welds.
Underwater Welding Safety Risks
Underwater welding mixes two dangerous jobs: welding and commercial diving. TWI names electrocution and drowning as key risks that training helps reduce.
- Electric shock: the AWS Welding Digest calls electrical exposure one of the most recognized hazards. Insulated gear, waterproof holders and surface-controlled power cut the risk.
- Decompression sickness: a fast ascent lets dissolved gases form bubbles in the body. Teams follow dive tables, ascent schedules and decompression procedures.
- Cold: water removes body heat much faster than air, so hypothermia is a real risk on long dives.
- Poor visibility and currents: wet welders work in murky water with moving currents, per the AWS Welding Digest.
Never try underwater welding without commercial diver training and a full dive team. It is not a home shop project.
Where Underwater Welding Is Used
Underwater welding repairs and builds structures that cannot come out of the water. TWI and AWS list these common jobs:
- Ship hulls and marine structures
- Offshore oil platforms
- Subsea pipelines
- Dams, bridges and harbor works
- Emergency repairs on damaged structures
TWI notes that much of this work happens in shallow water, or crews move a structure to a dry area first when they can.
Frequently Asked Questions
Is underwater welding done with stick welding?
Mostly, yes, for wet work. TWI says stick welding is often used for wet welding jobs, with electrodes that carry a waterproof coating over the flux. Flux cored wire is another wet option. Dry hyperbaric habitats let divers use TIG, MIG and plasma processes instead.
Does underwater welding use AC or DC?
Underwater welding uses direct current, not alternating current, according to TWI. The power source sits on the surface, and a double-pole knife switch lets the surface crew cut the current the moment the diver signals. The diver also wears rubber gloves and uses an insulated holder.
Why don’t underwater welders get electrocuted?
They stay fully insulated from the welding circuit. TWI notes divers use an insulated electrode holder and rubber gloves, and the surface crew switches power off as soon as welding stops. Training, DC power and strict dive procedures lower the risk, but electric shock stays a real hazard.
Is wet welding as strong as dry welding?
Usually not. TWI says dry welds tend to be better quality because the welder has more control over conditions. Wet welds cool fast and can pick up high levels of hydrogen, which raises the risk of cracking. Dry habitats get used when weld quality matters most.
How does the arc stay lit underwater?
The heat of the arc boils the water around it into a gas bubble. TWI says that vapor is about 70% hydrogen, 25% carbon dioxide and 5% carbon monoxide. The bubble shields the arc much like shielding gas does in air, so the arc keeps burning.
Final Words
Underwater welding works because the arc turns the water around it into a protective gas bubble. Wet welding uses that bubble directly with waterproof stick electrodes or flux cored wire.
Dry hyperbaric welding seals the joint inside a pressurized chamber and gives better welds with TIG, MIG or plasma arc.
Both methods run on DC power controlled from the surface, and both demand commercial diving skills on top of welding skills.


