Disclosure: This post contains affiliate links and I will be compensated if you make a purchase after clicking through my links. Learn More
What is air carbon arc gouging? It is a thermal process that melts metal with an arc from a carbon electrode and blows the molten metal away with a jet of compressed air. Welders use it to cut grooves, remove bad welds and prepare joints for welding on steel, stainless, cast iron and other metals.
You may also see it called air arc gouging, arc gouging or CAC-A (carbon arc cutting with air). It runs off a standard welding power source, a special torch and a shop air line, so many fab shops already own most of the gear.
Below we cover how the process works, the equipment, the setup numbers from manufacturer and industry guides, where it fits, and the safety steps it needs.
What Is Air Carbon Arc Gouging Used For?
Air carbon arc gouging is used to remove metal fast and in a controlled groove. ESAB lists the typical jobs as back gouging, removing excess weld metal, removing internal or surface defects and preparing bevel edges for welding.
- Back gouging: cutting out the root side of a full penetration weld so you can weld it again on sound metal.
- Defect removal: digging out porosity, slag inclusions and cracks found by inspection.
- Weld removal: taking off old or failed welds when you repair or take apart equipment.
- Weld reinforcement removal: flat electrodes take a weld cap down close to the plate surface.
- Joint prep and cutting: making U grooves and bevels, and cutting thick plate with a sawing motion.
How Air Carbon Arc Gouging Works
The torch holds a copper-coated carbon (graphite) electrode in a swivel head with air holes. You turn the air on, then lightly touch the electrode tip to the work to strike an arc.
The arc melts a small pool of base metal. The air jet runs along the electrode and blows that molten metal out of the joint, so a clean groove forms behind the arc. ESAB notes the metal is gouged only along the direction of the airflow.
The process does not depend on oxidation, which is how oxy-fuel cutting works. That is why it can gouge almost all metals, including stainless steel, cast iron and copper alloys that a cutting torch handles poorly.

Credit: www.youtube.com
Equipment You Need
Power Source
An industry guide based on Arcair data says the machine should be DC constant current, DC constant voltage or an AC/DC transformer with a 100% duty cycle. ESAB stresses constant current output so the electrode tip does not explode on contact.
ESAB puts the arc voltage between 35 and 55 volts. A loud arc is normal. A muffled arc points to low voltage, which can leave carbon deposits in the groove.
Polarity
Use DC electrode positive (DCEP) with DC electrodes on carbon steel, low alloy steel and stainless steel. ESAB and TWI list AC with AC electrodes for cast iron, copper and nickel alloys. The same guide notes AC is only about 50% as efficient as DC on carbon steel.
Electrodes
ESAB names 3 electrode types: DC copper-coated, DC plain and AC coated. DC copper-coated rods are the most common because the coating cuts electrode erosion and gives a longer life and a steadier arc.
Copper-coated rods come in round, half-round and flat shapes. Round and half-round rods cut U grooves. Flat rods make rectangular grooves and take off weld reinforcement. If rods get damp, the Arcair-based guide says to bake them for 10 hours at 300°F.
Torch and Air Supply
Most manual torches are air cooled. Heavy, high current torches use water-cooled cables. The air supply should be clean and dry, with an air dryer on the compressor, and the air hose to the torch should have an inside diameter of at least 3/8 inch.
Air volume is the number that catches people out. The Arcair-based guide calls for at least 80 psi with 25 to 33 cfm when the torch runs. Compare that with your compressor’s cfm rating at 80 psi before you buy a torch.
Air Carbon Arc Gouging Settings Chart
These DCEP current ranges come from Table 2.2 of Suggestions for Air Carbon Arc Gouging (RC Technical Services), which draws on Arcair and AWS C5.3 data. Start with the chart on your electrode box, since brands differ.
| Electrode diameter | DC electrode, DCEP (amps) |
|---|---|
| 5/32 in (4 mm) | 90 to 150 |
| 3/16 in (5 mm) | 200 to 250 |
| 1/4 in (6 mm) | 300 to 400 |
| 5/16 in (8 mm) | 350 to 450 |
| 3/8 in (10 mm) | 450 to 600 |
| 1/2 in (12 mm) | 800 to 1,000 |
| 5/8 in (16 mm) | 1,000 to 1,250 |
How to Read This Chart
Pick the electrode by the groove you need, then set the current inside its range. The groove comes out about 1/8 inch wider than the electrode diameter. The same guide warns that more amperage is not better, so stay inside the range.
Your torch also has a limit. Arcair Angle-Arc torches are rated from 450 amps (K2000) up to 1,250 amps (K5000), so match the rod size to the torch.
Other Key Settings
| Setting | Typical value | Source |
|---|---|---|
| Air pressure | 80 to 100 psi | ESAB |
| Air volume | 25 to 33 cfm minimum | Arcair-based guide |
| Electrode stickout, steel | 2 in minimum, 7 in maximum | Arcair-based guide |
| Electrode stickout, aluminum | 3 in maximum | ESAB |
| Push angle for gouging | 35 to 45 degrees from the work | ESAB |
| Push angle for cutting | 10 to 20 degrees from vertical | Arcair-based guide |
How to Air Arc Gouge: Basic Technique
Technique decides groove quality more than the machine does. These steps follow the ESAB and Arcair-based guidance.
Step 1: Set Up the Torch
Clamp the electrode with no more than 7 inches of stickout and at least 2 inches. Put the copper-coated end in the jaws so the uncoated tip faces the work. Turn the head so the air holes sit under the electrode, between the rod and the work.
Step 2: Turn the Air On First
Open the air valve before you strike the arc. Striking with no air lets carbon and molten metal stay in the groove.
Step 3: Strike and Push
Lightly touch the tip to the work. Do not pull the electrode back to set an arc length. Hold a push angle of about 35 to 45 degrees and move forward with the air blowing from behind the arc.
Step 4: Control Depth With Speed and Angle
A faster travel speed makes a shallow gouge. A slower speed makes a deeper one. A steeper angle also cuts deeper. The right speed gives a smooth hissing sound.
Step 5: Use Several Passes for Deep Grooves
ESAB says a groove deeper than 1.5 times the electrode diameter needs more than one pass. For a groove wider than the rod, move the electrode side to side. TWI advises a side-to-side width no more than 4 times the electrode diameter.

Credit: www.youtube.com
Common Mistakes to Avoid
- Backing up or reversing the torch, which leaves carbon deposits.
- Running too little air pressure, which traps carbon in the gouge.
- Turning the current above the chart range for the rod.
- Burning the stickout below 2 inches, which can damage the torch head.
- Using a cylinder of oxygen in place of compressed air. The Arcair-based guide says never do this.
Carbon Pickup and Groove Quality
The molten metal picks up carbon from the electrode. With good technique and enough airflow, the air jet blows that carbon-rich metal out and the sidewalls stay clean, according to TWI.
Poor technique, low airflow or a very steep electrode angle can leave a carbon-rich layer. That layer can be hard and can crack when you weld over it. TWI advises grinding the groove sidewalls if that layer forms, and dressing crack-sensitive steels by grinding after gouging.
Preheat matters too. The Arcair-based guide says to preheat for gouging whenever the welding procedure calls for preheat. For repair work it suggests about 50°F above the welding preheat.
Pros and Cons of Air Carbon Arc Gouging
| Pros | Cons |
|---|---|
| High metal removal rate | Very loud, often above safe hearing limits |
| Works on almost all metals | Throws molten metal a long distance |
| Runs on a standard welding power source | Heavy smoke and fumes |
| Close control of groove shape | Needs a lot of compressed air (25 to 33 cfm) |
| Simple to learn for a welder | Poor technique can leave a hard, carbon-rich layer |
Safety Tips for Air Carbon Arc Gouging
Noise is the hazard people underrate. A NIOSH study by Lowe and Mechling (2014) found the process exposes workers to 94 to 125 dB(A), enough for a hazardous dose in as little as 3 seconds. Wear hearing protection, and make sure people nearby wear it too.
- Fire: sparks and molten metal fly far. Clear combustibles from the area or post a fire watch.
- Fumes: the process makes a large amount of smoke, fumes and gases. Provide ventilation and keep your head out of the plume.
- Arc and burns: wear a welding helmet, flame-resistant clothing, leather gloves and boots. Molten metal spray finds every gap.
- Electrical: use a power source with enough capacity for the job, and follow the maker’s advice before you parallel machines.
- Air: use compressed air only. Never hook the torch to oxygen.
Frequently Asked Questions
What is the difference between arc gouging and plasma gouging?
Air carbon arc gouging melts metal with a carbon electrode arc and blows it out with shop air. Plasma gouging uses a plasma cutter with a gouging tip and a constricted plasma arc. Carbon arc gouging runs on a standard welding machine. Plasma gouging needs a plasma system.
What polarity is used for carbon arc gouging?
Use DC electrode positive (DCEP) with DC copper-coated electrodes on carbon steel, low alloy steel and stainless steel. ESAB and TWI list AC with AC electrodes for cast iron, copper and nickel alloys. Check the electrode maker’s chart, since rod type and polarity must match.
How much air pressure do you need for arc gouging?
ESAB recommends 80 to 100 psi at the torch. Volume matters as much as pressure. The Arcair-based guide calls for at least 25 to 33 cfm during gouging, so a small compressor may drop pressure and leave carbon in the groove.
Can you carbon arc gouge stainless steel?
Yes. ESAB lists DC power for steel and stainless steel because the process does not rely on oxidation. Good airflow and steady travel matter on stainless, since a carbon-rich layer left in the groove can harm the weld. Grind the sidewalls if you see that layer.
Can you arc gouge with a stick welder?
Yes, if it has the output for the rod size. The Arcair-based guide wants a constant current, constant voltage or AC/DC machine with a 100% duty cycle. A 5/32 inch rod runs at 90 to 150 amps, so small rods suit lighter stick welders.
Final Words
Air carbon arc gouging is a fast, simple way to cut grooves and remove welds on almost any metal with a welding machine, a torch and shop air. Most problems come from too little air, the wrong current or poor travel speed.
Start with the chart on your electrode box, set 80 to 100 psi, keep a steady push and listen for the hiss. Protect your hearing every time, because the noise reaches harmful levels in seconds.


