How Tall Should a Welding Table Be? Height by Your Elbow

Disclosure: This post contains affiliate links and I will be compensated if you make a purchase after clicking through my links. Learn More

How tall should a welding table be? For most people standing at the table, a welding table should be about 2 to 4 inches below your elbow height, which puts most fixed tables in the 34 to 40 inch range.

There is no single right number. Many commercial tables ship near 36 inches, but your arm length, your process and the size of your parts change the best height.

We show you how to measure your own height, how to adjust it for TIG, MIG and grinding, and what to do if your table is already built.

How Tall Should a Welding Table Be? The Short Answer

Set the top of your welding table about 5 to 10 cm (2 to 4 inches) below your standing elbow height for general welding and fitting. That is the light work range in the CCOHS standing work guide, and it fits most MIG and stick work on a bench.

For a person with a 42 inch elbow height, that works out to about 38 to 40 inches. A shorter welder needs less, and a taller welder needs more.

Why Welding Table Height Matters

A table that sits too low makes you bend at the waist and lean over the joint. Hours of that adds up to back and neck strain.

A table that sits too high pushes your shoulders up and your elbows out. Your arms tire faster, and your torch or stinger angle gets harder to hold steady.

Leaning low also puts your face closer to the fume plume. Keep your head out of the plume no matter how tall your table is.

Welder working at a bench, showing welding table height and back posture

Credit: www.youtube.com

How to Find Your Ideal Welding Table Height

Use your elbow as the guide, not your total height. CCOHS says to “adjust the height of the work according to body dimensions, using elbow height as a guide.”

Step 1: Measure Your Elbow Height

Stand straight in the boots you wear in the shop. Let your upper arm hang down and bend your elbow to 90 degrees.

Have someone measure from the floor to the underside of your forearm at the elbow. Write that number down in inches.

Step 2: Pick the Work Type You Do Most

CCOHS lists three working height ranges for standing work, all measured from elbow height:

  • Precision work: about 5 cm (2 inches) above elbow height, with elbow support.
  • Light work: about 5 to 10 cm (2 to 4 inches) below elbow height.
  • Heavy work with downward force: about 20 to 40 cm (8 to 16 inches) below elbow height.

For welding, we map these ranges to the jobs you do at the table. Small part TIG work is close to precision work. General MIG, flux core and stick work is light work. Heavy grinding, hammering and fitting thick plate is closer to heavy work.

Step 3: Subtract Your Part and Fixture Height

The table top is not your working height. Your joint sits on top of the part, the fixture or the vise.

If your parts sit 3 inches above the table on blocks or squares, lower the table by about 3 inches to keep the joint at the same height.

Welding Table Height Chart by Elbow Height

This chart uses the CCOHS ranges converted to inches (5 cm is about 2 inches, 10 cm about 4 inches, 20 cm about 8 inches and 40 cm about 16 inches). Values are rounded to the nearest inch.

Elbow heightPrecision (TIG, small parts)Light work (MIG, stick, fitting)Heavy work (grinding, hammering)
40 in42 in36 to 38 in24 to 32 in
42 in44 in38 to 40 in26 to 34 in
44 in46 in40 to 42 in28 to 36 in

The precision row assumes you rest your forearm or elbow on the table or a support. Without support, a precision height that high tires your shoulders fast.

Worked Example: Setting a Table for a 42 Inch Elbow

Say your elbow height is 42 inches and you mostly MIG weld brackets that sit flat on the table.

  1. Light work range: 42 minus 4 inches equals 38 inches, and 42 minus 2 inches equals 40 inches.
  2. Your parts sit flat, so there is no fixture height to subtract.
  3. Set the table top at 38 to 40 inches.

Now say you weld the same brackets on 2 inch tall fixture blocks. Drop the table to about 36 to 38 inches so the joint stays at the same height.

Standard Welding Table Heights From Makers

Many fixed and modular tables sit close to 36 inches. Here is what a few makers list:

  • Siegmund System 28 Imperial BASIC: the 35 inch standard leg gives a 36 inch table top height, with 1-5/16 inch of fine adjustment.
  • Siegmund 750 mm standard leg (sold by Strong Hand Tools): the leg is 29.5 inches tall and Strong Hand lists a 36.5 inch working height on a Siegmund table.
  • Siegmund adjustable height leg (Strong Hand Tools): the legs adjust from 21.5 to 35.5 inches and set the working height at 29.5 to 43.5 inches.
  • Texas Metal Works: builds its tables at 38 inches as standard and says the common 36 inch height makes many welders lean forward.

Texas Metal Works also gives a chart by welder height, from 34 to 36 inches for a 5 foot 2 inch to 5 foot 4 inch welder up to 42 to 44 inches for someone over 6 foot 4 inches. It is a vendor rule of thumb, so check it against your own elbow measurement.

Fixed vs Adjustable Height Welding Tables

A fixed table has no height parts to loosen or lose. It works well if one person uses it for the same kind of work every day.

An adjustable table makes sense when more than one person welds at it, or when you switch between TIG on small parts and fitting heavy weldments. The Siegmund adjustable leg covers a 14 inch range, from 29.5 to 43.5 inches of working height.

Adjustable height welding table raised to a taller working height

Credit: www.youtube.com

CCOHS adds that if a work surface cannot be adjusted, a platform can raise a shorter worker. For a taller worker, a pedestal or riser on top of the work surface does the same job.

How to Fix a Table That Is the Wrong Height

  • Too low: bolt leg extensions or a riser frame under the legs, or weld on taller leveling feet. A heavy steel plate or fixture block on top also raises the work.
  • Too high: stand on a sturdy, non slip platform that covers your whole working area. Cut the legs down only if you are the only person who uses the table.
  • Mixed jobs: keep the table at your light work height and raise small TIG parts on blocks or a bench vise.

Whatever you do, keep the table stable and level. A wobbly riser is worse than a table that is an inch off. If you are still planning the table, think about the welding table holes and fixtures you will use, since they change your working height.

Frequently Asked Questions

What is the standard height of a welding table?

Many welding tables sit close to 36 inches. Siegmund lists a 36 inch top height with its 35 inch System 28 Imperial standard leg. Texas Metal Works builds at 38 inches. The best height for you still depends on your elbow height and the kind of welding you do.

Should a welding table be the same height as a workbench?

Not always. A workbench is often set for sawing, filing and assembly. A welding table should put the joint 2 to 4 inches below your elbow for general welding. If you do both jobs on one surface, set it for the work you do most and use risers.

What height should a TIG welding table be?

TIG on small parts is close to precision work, which CCOHS puts about 2 inches above elbow height with elbow support. Many TIG welders sit instead. When seated, set the table so your forearms rest on it and your shoulders stay relaxed, not raised.

Is 36 inches too short for a welding table?

Texas Metal Works says the common 36 inch height makes many welders lean forward. A welder with a 42 inch elbow height would aim for about 38 to 40 inches for general welding. For a shorter welder, 36 inches can be right. Measure your elbow height first.

How do I raise my welding table height?

Add leg extensions, taller leveling feet or a riser frame under the legs. On modular tables, adjustable legs like the Siegmund adjustable leg set the work height from 29.5 to 43.5 inches. You can also raise the part with fixture blocks, which keeps the table itself unchanged.

Final Words

The right welding table height starts at your elbow. For most standing welding, aim for 2 to 4 inches below elbow height, then subtract the height of your parts and fixtures.

If more than one person uses the table, or you swing between TIG and heavy fitting, adjustable legs or risers save your back. Measure once, set the table, and weld a few test joints before you call it done.

Scroll to Top